Sometimes we need to protect business or private life without revealing it. Now you have a possibility to do it without any hindrance. This super portable gadget allows you to protect yourself and check room or environment without being noticed. Perfect device, If you need full protection. Due to very small size, always convenient to take this gadget with you wherever you go. Miniature dimensions, soundless signal — nobody is aware you have been informed.
RAKSA 911 detects:
phones of GSM900/1800, UMTS 900/2100 (3G), CDMA450 standards;
This super small and fast scanner, will automatically detects and classifies all dangerous signals and informs you instantly with full information about each. It provides continuous scanning of frequency range and analysis of spectrogram peaks. The standard digital signals are identified by their amplitude-time characteristic. Scanning and analyzing cycle period is only 1.0-1.5 sec. Filtration of short-term noise requires at least two scanning cycles, so the signal is detected in 2-3 seconds.
High-tech scanning system will automatically determine Analog or Digital signals. Any continuous radio signal with the amplitude modulation index ?0.5 without frequency hopping is treated as an analog signal. Such are the analog signals of AM, FM, PM modulation and digital signals of FSK, PSK and the like modulations.
multifunctional Detector can operate in 5 modes:
RAKSA differ by high sensitivity and super small size. High-tech professional level are also available for everyday use. Raksa iDet was tested in "DAkkS" EMC Testlaboratory. According to an official tests, the device fully complies with the technical characteristics stated by the manufacturer. This professional Detector Provides ultimate Protection.
Bug Detectors of such small size, sensitivity and usability has ever had! This Detector will control all undesired events in real time and if happen undesirable precedent it will instantly find a threat! Using Raksa will protect your private life and business from uninvited intrusion.
Don't let others penetrate your business and private life.
Guard Mode provides continuous monitoring of detected analog and digital radio signals in automatic mode and setting alarm in case of threat radio signal (signal exceeding the preset threshold level) detection. Guard Mode is used in cases when the primary signal source has not been activated. The information about the alarm events is recorded in the Alarm Log.
Guard Mode enables the background noise deduction for analog signals thus reducing the influence of regular background noise. Slow fluctuations of its level are ignored thanks to the adaptation algorithm.
Sweep Mode is used for detection of analog and digital radio signals of all types. This mode allows the review of all detected signals regardless their level.
The Search Mode is used for detection and location of analog and digital transmitters. This mode is used when you can move the RF Detector around searching for a radio transmitter.
Search Mode for analog signals utilizes both light and sound indication of the signal strength: the higher is the frequency of flash the closer is the transmitter.
Difference Search Mode
Difference Search Mode is used for detection and localization of analog transmitters. This mode has its advantage in case the transmitter is located in the same room.
In this Mode the device defines the relative level of the signal — its difference with the reference spectrum that was fixed at the beginning of operation in this Mode. The closer to the source of radio signal located in the room the higher is its signal level in comparison with the outside radio transmitter. The RF Detector selectively reacts to the change of level thus enabling to locate the radio transmitter at a higher rate.
Differential Search Mode utilizes both light and sound indication of the relative signal level.
Monitoring of Digital Signals
Monitoring of Digital Signals is intended for detection of mobile phone signals (GSM900/1800, UMTS(3G), CDMA450 types), cordless telephones (DECT standard), Bluetooth, Wi-Fi and other impulse signals in 2.4 GHz.
In Monitoring of Digital Signals the display shows the list of all digital signals and their strength levels.
Audio Monitoring is available only for analog signals in Sweep, Search and Difference Search Modes through the built-in speaker. The audio monitoring facilitates signal identification and allows using the acoustic feedback.
Alarm Events Log
Alarm Events Log accumulates the information about the threat signals detected in the Guard Mode. The max number of records ? 200. If the detected threat signals are of different types the Log will record all of them. The display shows the moment of detection and the moment of the signal extinction, the type and the max level of the signal.
What's in the box